5150 AutoSport Head Gasket & Head Stud Kit, BMW B58 Gen1

5150 AutoSport Head Gasket & Head Stud Kit, BMW B58 Gen1

SKU: 5150-autosport-head-gasket-head-stud-kit-bmw-b58-gen1 Category: Tags:

Description

Head Gasket

The Cometic MLX Head Gasket is specifically engineered for use in B58 turbocharged inline 6-cylinder engines found in various BMW chassis and the Toyota GR Supra A90/A91.

Gen 1 replaces BMW part # 11128654268 and #11128654269.

Gen 2 replaces Toyota part # 11115WAA04

C14144-036, C14144-040, C14144-042, C14144-04052

Constructed with multiple layers of stainless steel and a proprietary coating, the MLX gasket offers superior sealing and load distribution capabilities. The coating is designed to withstand high temperatures and pressures, preventing gasket failure due to fatigue or stress. Additionally, the unique embossed sealing bead provides further sealing ability.

It’s important to note that MLS/MLX head gaskets are not compatible with engines that have O-rings or receiver grooves around the cylinder bores. These gaskets require smooth and flat surfaces to seal properly.

Head Gasket Installation instructions:

  1. Make sure that the engine block and cylinder head surfaces are clean, flat, and free from any debris, oil, or coolant.

  2. Install the MLS gasket on the engine block and ensure that it is properly aligned. Avoid twisting or bending the gasket during installation.

  3. Place the cylinder head on top of the gasket and install the head bolts or studs in their correct positions.

  4. Follow the manufacturer’s recommended torque specifications and tighten the bolts or studs in the proper sequence to ensure even clamping force across the gasket.

  5. After the initial tightening, re-torque the head bolts or studs after the engine has been started and then allowed to cool to room temperature. This will ensure that the gasket is properly seated and compressed.

  6. It is recommended to not use any additional sealant on the MLS gasket, as it is already coated with a Viton rubber sealant. Using additional sealant can hinder the performance of the gasket.

 

Head Stud Kit:

The ARP2000 Head Stud Kit, 203-4705, is designed for the turbocharged inline 6-cylinder B58 engines found in various BMW chassis and the Toyota GR Supra A90/A91.  As you increase the power output of your engine beyond its factory specifications, the head and block may start to separate, causing factory bolts to stretch and fail. ARP Head Studs are stronger than factory bolts, ensuring your race engine stays together even under extreme conditions.

The Custom Age 625+ option, 203-4706, is made from a material that has a tensile strength of 260 ksi, which is substantially higher than the 190 ksi of the ARP 2000 head stud. It’s an ideal choice for individuals who want to push the limits of their B58 builds and require a stronger head stud.


Head Stud Kit Installation Instructions: 

1. To ensure proper thread engagement and accurate torque readings, clean ALL threads in the block. Chase if necessary with ARP Thread Chaser.
2. Clean and inspect all hardware prior to installation. Look for obvious defects or shipping damages, plus proper fit, length and dimension.
3. If the cylinder head studs protrude into a water jacket, lubricate the block threads of the studs with ARP THREAD SEALER.
4. Screw studs into the block “HAND TIGHT ONLY”.
5. Install the cylinder head(s) and check for binding or misalignment.
6. Lubricate the stud threads, nuts and washers with ARP ULTRA-TORQUE FASTENER ASSEMBLY LUBRICANT.
Then install the washers and the nuts onto the studs and tighten them hand tight.
ARP recommends using the ARP ULTRA-TORQUE FASTENER ASSEMBLY LUBRICANT that is provided with each kit as opposed to motor oil. This is due to higher friction on the studs as well as inconsistencies in the clamping force of the fasteners when motor oil or other low quality lubricants are used.

PRELOAD (TORQUE) RECOMMENDATIONS

7. Following the manufacturers recommended torque sequence tighten the nuts steps 1-3

ARP2000
Step 1: Tighten to 30 ft-lbs.
Step 2: Tighten to 60 ft-lbs.
Step 3: Tighten to 90 ft-lbs.
Custom Age 625+
Step 1: Tighten to 30 ft-lbs.
Step 2: Tighten to 60 ft-lbs.
Step 3: Tighten to 100 ft-lbs.

with ARP Ultra-Torque fastener assembly lubricant

Bolt Torque Sequence

 12  10 4 2 6 8 14
13 7 5 1 3 9 11

Reviews

There are no reviews yet.

Be the first to review “5150 AutoSport Head Gasket & Head Stud Kit, BMW B58 Gen1”

Your email address will not be published. Required fields are marked *

12345

Related products